1

Тема: COULD NOT LOAD EXTERNAL CODE: 1

Добрый день!
Подскажите, иожет кто сталкивался, при загрузке навигатора 07, не загружается дальше лого с машиной.
В логу ошибка:  COULD NOT LOAD EXTERNAL CODE: 1

Полный лог:
[06/30/19 01:58:36] Device started
[06/30/19 01:58:36] Gather SysInformation
[06/30/19 01:58:36] Init EMC
[06/30/19 01:58:37] Main started
[06/30/19 01:58:37] SDRAM test start...
[06/30/19 01:58:37] set sys state: 2
[06/30/19 01:58:37] test data bus...
[06/30/19 01:58:37]   ok
[06/30/19 01:58:37] test address bus...
[06/30/19 01:58:37]   ok
[06/30/19 01:58:37] OK
[06/30/19 01:58:37] SDRAM test OK
[06/30/19 01:58:37] Build Time: Nov  6 2015 14:11:54 ( 1446819114 )
[06/30/19 01:58:37] Create task Init
[06/30/19 01:58:37] Start sheduler
[06/30/19 01:58:37] set sys state: 6
[06/30/19 01:58:37] Task SysTmr created
[06/30/19 01:58:37] Queue for task SysTmr created
[06/30/19 01:58:37] Init GPIO
[06/30/19 01:58:37] Init Driver 10
[06/30/19 01:58:37] Success
[06/30/19 01:58:37] MCI_disk_initialize
[06/30/19 01:58:38] MCI_INIT ok
[06/30/19 01:58:43] MCI_Send_ACMD failed, MMC or invalid power-range or no card
[06/30/19 01:58:45] MCI_INIT ok
[06/30/19 01:58:50] MCI_Send_ACMD failed, MMC or invalid power-range or no card
[06/30/19 01:58:50] unknown card
[06/30/19 01:58:50] Check_CID failed
[06/30/19 01:58:50] Set_Address failed
[06/30/19 01:58:50] Send CSD failed
[06/30/19 01:58:50] Select Card failed
[06/30/19 01:58:50] Set Block Length - failed
[06/30/19 01:58:50] Init driver FLASH
[06/30/19 01:58:51] Semaphore init
[06/30/19 01:58:51] PCT25 Flash detected
[06/30/19 01:58:51] Success
[06/30/19 01:58:51] Init parameters
[06/30/19 01:58:51] disk_initialize(0) - ERROR
[06/30/19 01:58:51] auto_mount - ERROR 1
[06/30/19 01:58:51] disk_initialize(0) - ERROR
[06/30/19 01:58:51] LenParam = 8977
[06/30/19 01:58:51] disk_initialize(0) - ERROR
[06/30/19 01:58:51] auto_mount - ERROR 1
[06/30/19 01:58:51] disk_initialize(0) - ERROR
[06/30/19 01:58:51] Config: LenParam = 873
[06/30/19 01:58:51] Success
[06/30/19 01:58:51] ------------------------------------
[06/30/19 01:58:51] ------------------------------------
[06/30/19 01:58:51] RESET: External Reset
[06/30/19 01:58:51] DEVICE: N.07.111 - 128093
[06/30/19 01:58:51] FIRMWARE: Nov  6 2015 RLS
[06/30/19 01:58:53]    Try to decompress resource file...
[06/30/19 01:58:53]    Decompress OK. File len: 407338
[06/30/19 01:58:53] Init Display Driver
[06/30/19 01:58:53] Init Driver 2
[06/30/19 01:58:53] UC1608 init
[06/30/19 01:58:54] Success
[06/30/19 01:58:54] GLCD: Open Display Driver
[06/30/19 01:58:54] PRM: callback CallBackNew_LCD
[06/30/19 01:58:54] PRM: Ok
[06/30/19 01:58:55] PRM: callback CallBackNew_LCD
[06/30/19 01:58:55] PRM: Ok
[06/30/19 01:58:55] System state: 0, lifetime: -13703425
[06/30/19 01:58:55] Init BootService: res.= 0
[06/30/19 01:58:55] Init extarnal modules
[06/30/19 01:58:55] Failed, res: 1
[06/30/19 01:58:55] set sys state: 11
[06/30/19 01:58:55] COULD NOT LOAD EXTERNAL CODE: 1

Старым Blazemaster прошивать пробовал, не помогает. При перепрошивке гаснет , blaze  переберает скорости но увы.

2 (09-07-2019 16:09:23 отредактировано Яргортранс)

Re: COULD NOT LOAD EXTERNAL CODE: 1

У нас большинство подобных вылечивалось перепрошивкой, одному не помогло, пришлось перепаивать микруху памяти AT45, после этого заработал.

Навигационная система пассажирских перевозок г.Ярославля.
Используемое оборудование - Гранит 02, 04, 06, 2.07, 2.08, 4.10, 4.11, 4.14, 6.18.